Plumbing 101: A Necessity for Bathtub Installation
Plumbing 101: A Necessity for Bathtub Installation
Blog Article
Just how do you really feel in relation to Tools You Need to Install a New Bathtub ?
Installing a bathtub isn't specifically brain surgery, yet it does require strong plumbing, woodworking, as well as occasionally, tiling skills. Replacing an old tub with a brand-new one is additionally a reasonably challenging project. If the old tub is conveniently easily accessible, the task can relocate rapidly; if you need to open up a wall to remove the old tub as well as position the new bathtub, the task is much harder. In either case, the task is within a house handyman's abilities, although you will certainly need a helper to vacate the old bathtub as well as set in the new one. Make sure you have qualified yourself for the job and fit attempting it. Instead of employing a specialist to take control of a halfway-completed task, it is much better to think about employing one before you start. Possibilities are you may require a specialist plumber to make tube connections.
This article will help you set up a brand-new bathtub in your shower room if you have actually already bought a new tub as well as don't require to transform the arrangement of your previous water supply pipelines.
Your devices and material checklist must consist of the following:
Removing Old Touches
If you need to change old taps with new ones as a part of your installation, then the first thing you ought to do is disconnect the water supply. After doing so, activate the faucets to drain pipes any kind of water continuing to be in the system. The process of removing the existing taps can be quite problematic due to the limited access that is often the case.
Make use of a container wrench (crowsfoot spanner) or a faucet tool to undo the nut that connects the supply pipes to the faucets. Have a towel prepared for the remaining water that will come from the pipelines. Once the supply pipes have actually been removed, utilize the exact same device to loosen the nut that holds the taps onto the bath/basin. You will require to stop the single taps from turning during this procedure. When the faucets have actually been eliminated, the holes in the bath/basin will certainly need to be cleaned of any type of old securing compound.
Before carrying on to fit the brand-new taps, contrast the pipe connections on the old taps to the brand-new faucets. If the old taps are longer than the new faucets, then a shank adapter is needed for the brand-new faucets to fit.
Fitting New Touches
If the tails of the brand-new taps are plastic, then you will need a plastic adapter to prevent damage to the thread. One end of the adapter fits on the plastic tail of the faucet as well as the various other end gives a link to the existing supply pipelines.
If you require to fit a monobloc, then you will require minimizing couplers, which connects the 10mm pipeline of the monobloc to the typical 15mm supply pipe.
Next off, place the faucet in the installing opening in the bath/basin guaranteeing that the washers remain in place between the tap and the sink. Protect the tap in position with the manufacturer offered backnut. Once the tap is securely in position, the supply pipes can be attached to the tails of the taps. The taps can either be linked by utilizing corrugated copper piping or with regular tap ports. The former type ought to be linked to the faucet ends first, tightening up only by hand. The supply pipelines can later on be connected to the various other end. Tighten up both ends with a spanner after both ends have actually been attached.
Setting up the Bathtub
Using both wooden boards under its feet, position the bathtub in the needed position. The wood boards are helpful in equally spreading out the weight of the bath tub over the location of the boards instead of focusing all the weight onto 4 tiny factors.
The next objective is to ensure that the tub is leveled all round. This can be achieved by inspecting the level and adjusting the feet on the tub up until the spirit level reads level.
To set up taps, fit the bottom of the furthest versatile faucet adapter to the suitable supply pipeline by making a compression join; then do the exact same for the various other faucet.
Switch on the supply of water and also inspect all joints and new pipework for leaks as well as tighten them if necessary. Fill up the bathtub as well as also examine the overflow electrical outlet and the normal outlet for leaks.
Finally, take care of the bathroom paneling as defined in the manufacturer's user's manual. Tiling and sealing around the bathtub should wait until the tub has actually been used at least once as this will certainly resolve it right into its last position.
Planning for the Setup
To start with, the supporting frame supplied with the bath needs to be fitted (if required) according to the producer's instructions. Next off, fit the faucets or mixer to the tub. When fitting the tap block, it is essential to ensure that if the faucet features a plastic washer, it is fitted between the bath and also the taps. On a plastic bathroom, it is likewise reasonable to fit a sustaining plate under the faucets system to avoid strain on the tub.
Fit the flexible faucet adapters to the bottom of the two taps making use of 2 nuts and olives (occasionally provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and afterwards pass the electrical outlet through the hole in the bath. Make use of the nut provided by the producer to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the flexible overflow pipe to the overflow outlet. After that, screw the pipeline to the overflow face which must be fitted inside the bathroom. Make certain you utilize all of the provided washers.
Attach the trap to the bottom of the waste electrical outlet on the bath tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Link the bottom of the overflow tube in a comparable manner.The bathroom ought to now be ready to be fitted in its last position.
Tiling Around the Bath tub
In the location where the bathroom satisfies the ceramic tile, it is needed to seal the joins with a silicone rubber caulking. This is essential as the fitting can move sufficient to break a stiff seal, creating the water to penetrate the wall between the bathroom as well as the tiling, causing complications with moisture as well as possible leaks to the ceiling listed below.
You can choose from a variety of coloured sealants to assimilate your components as well as installations. They are offered in tubes and also cartridges, and can sealing spaces approximately a size of 3mm (1/8 inch). If you have a bigger gap to load, you can load it with twists of soaked newspaper or soft rope. Remember to constantly load the bathtub with water before sealing, to allow for the movement experienced when the tub is in use. The sealant can split fairly early if you do not take into account this motion prior to securing.
Alternatively, ceramic coving or quadrant tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as cut to dimension, are additionally conveniently available on the market. It is a good idea to fit the floor tiles using waterproof or water-proof adhesive and also grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Do you like more info about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround? Write feedback directly below. We'd be delighted to know your suggestions about this blog. Hoping that you visit us again later on. Are you aware of anybody else who is fascinated with Installing A Bathtub? Why not promote it. Kudos for your time. Come back soon.
No more waits, dial now! Report this page